The basin is a sanitary ware that every bathroom must have. People wash it every day, and place small objects. Then, in the face of different styles of basins, the installation process will be different, and it will not work in this way. Xiaobian brings a full tutorial of the basin installation process, each of which breaks through the puzzles. Washing table installation matters Washing table installation notes: 1, pay attention to the height of the washstand When manufacturing the installation of the washstand, you should pay attention to its height. Generally, the height of the countertop from the ground is about 75-90cm, and the height can be selected according to personal habits. 2, pay attention to the cooperation between the wash basin and the faucet Many times there will be a tap and the water will splash out. This is because the wash basin and the faucet are not suitable. The deeper wash basin can be matched with the faucet with a stronger intensity, while the shallower wash basin is not suitable for the strong wash. Pot, so there is water splashing out. 3. Space decision form The washbasin is roughly divided into two types: independent and desktop. The independent styling is beautiful, the occupied space is small, and the suitable space is small. The space is larger, the desktop is also good, the function is complete, and it is convenient to use. How to install a vanity: First, the basin material classification According to the material, the basin can be divided into ceramic basin, glass basin, stainless steel basin, artificial stone basin and so on. Among them, ceramic basins are the most common and the price is average. Glass material basin cleaning is difficult; stainless steel material is easy to clean, but suitable for single style; artificial stone basin is more expensive. Second, the basin installation needs to know Basin installation is a very critical step. Because different manufacturers choose different basin products, the installation methods are different. The following small series will tell you about the installation of several common basins. 1. Installation method of above counter basin The installation of the above counter basin is relatively simple. Just open the hole at the predetermined position on the countertop according to the installation drawing, then place the basin in the hole and fill the gap with glass glue. 2. Installation method of under counter basin The installation of the under counter basin is more complicated than the installation of the above counter basin. Firstly, the mounting bracket should be customized according to the size of the under counter basin, and then the under counter basin should be installed at the predetermined position. After the bracket is fixed, the countertop with the opened hole is placed under the counter. On the basin. When installing, be careful that the position of the bracket is fixed accurately. In addition, the hole should be rounded. 3, hanging pot installation method Hanging basins are generally mounted on the wall, which saves space. Let's take a look at the general installation method of the hanging pot. (1) By measuring, the installation height and center line are marked on the finished wall. The recommended installation height is 82cm. (2) Place the basin along the center line to the installation position, adjust it to center horizontally, and anchor the mounting hole on the wall. (3) Carefully open the basin and drill the appropriate bolt holes in the anchor holes on the wall. Install the suspension bolts on the wall and keep each bolt about 45 mm. (4) Level the basin, put on the gasket and tighten the nut until appropriate, and put on the decorative cap. (5) Place the bracket against the wall, align its position and then anchor the hole. Install the bracket on the wall and connect the basin to the bracket with four pieces of rubber. (6) Install the faucet and drain assembly according to the instructions for the purchased water, and connect the water inlet and drain. (7) Put a mildew-proof seal between the basin and the wall. 4, the column basin installation method The general method of installation of the pedestal is to first install the water purifier of the pedestal, then install the faucet and hose. Then place the pedestal porcelain column in the corresponding position, carefully put the pedestal basin on it, and notice that the lower water pipe is just inserted into the lower water pipe left by the original ground. Then connect the upper water pipe to the water inlet. Finally, glue the glass glue along the edge of the basin.
We manufacture a variety of refractory Metallized ceramics , mainly including Metallized Ceramic Insulator, Metallized Ceramic Tube, Metallized Ceramic Ring, Metallized Ceramic Substrate, Ceramic metallized cylinders.These Metallized Ceramics is fit for high vacuum, high voltage and high pressure applications due to their exceptional insulation strength, superb bonding strength and excellent metal to ceramic joining hermeticity.
We offer a selection of metallization types to meet special needs via screen printing, pad printing, brushing, the regular types as below:
â—Ceramic body base + Molybdenum (Mo/Mn) metallization.................â—Ceramic body base + Silver(Ag) plating
â—Ceramic body base + Tin (Sn) plating.................................................â—Ceramic body base + Molybdenum (Mo/Mn) + Nickle plating
â—Ceramic body base + Tungsten (W) + Gold plating........................... â— Ceramic Substrate + Copper(Cu) plating.
Based on in-house comprehensive manufacturing equipment from shaping to electroplating process, we have prototyping to high volume production capability. It helps us to make the dimensions consistency very well, also, helps us to offer a more competitive cost to our customers. Whatever, a very small trial order for R&D program, or extremely high volume need for cost down, we will find a optimal solution there to meet your needs.
These metallized ceramics are widely used in ceramic to metal, ceramic to ceramic joining technology in electrical, electronics, high vacuum technology, medical technology, sensor technology, the typical application like the ceramic insulator/body in vacuum interrupters, vacuum capacitors/thyristor, gas discharge tube, electron tubes, current feedthrough, X-ray tubes, power switches and so on.
Metallized ceramics Metallized Ceramics,Vacuum Device Ceramics,Vaccum Tight Ceramics,Vacuum Ceramic Component Jinghui Industry Ltd. , https://www.ceramictek.com