Emery wear-resisting ground material is the common name for domestically-used hardened ground. It has the advantages of abrasion resistance, pressure reduction, dust reduction, hard surface, easy cleaning, economy and durability. Because of its convenient construction, non-pollution, low cost, long service life and other characteristics, it has made an astonishing growth rate in cities with relatively developed coastal industries such as the Yangtze River Delta and the Pearl River Delta. Now it has become popular in China. So, what are the characteristics of emery wear-resistant flooring ? What is the construction process of emery wear-resistant floor materials ? Let's take a look together. Emery wear-resistant flooring material features Emery wear-resistant flooring is suitable for ground decoration needs in industrial sites, docks, workshops, logistics warehouses, supermarkets, parking lots, squares, and sports grounds. Emery wear ground features: 1, the color is optional, the common color is only the cement primary color, gray, green, red, etc., the surface is dense, easy to dust, easy to clean; 2. It is a substitute for traditional industrial surface terrazzo. 3. Simultaneous construction with concrete can be quickly put into use; 4, low cost, high cost performance. long lasting; 5, wear resistance, impact resistance, excellent pressure resistance. Basic requirements 基 The concrete strength of the grass-roots level shall be higher than C25, the water-cement ratio shall be controlled below 0.50, the difference between the concrete fall-out shall be controlled within 70-100mm, and the concrete mixture shall minimize segregation and control the bleeding. ◇ In order to ensure that the concrete mix has sufficient fluidity and conducive to construction, it is recommended that concrete be added with appropriate additives. 基 The concrete of the grass-roots level shall be poured and tamped with reference to the standard of high-quality concrete. Pay attention to the precise dimensions and reduce the production of laitance. 硬化 The hardener surface is preferably constructed at the same time as the concrete structure layer. If it is necessary to work with the leveling layer at the same time, it is recommended that the leveling concrete should be fine-grained concrete with a thickness of not less than 50mm, and a telescopic reinforcement mesh should be considered. ◇ Pay special attention to the corners of the concrete construction block of the primary floor to ensure that the concrete at the site is vibrated and compacted, and additional strengthening measures should be taken. Emery wear-resistant ground construction process Concrete construction requirements: According to the design requirements, the concrete shall be poured to an elevation of plus or minus zero and the concrete mark ≥C25 and the thickness more than 5cm. The first time the material was spattered: The prescribed amount of 2/3 of the wear-resistant material was evenly spread on the surface of the newly set concrete. The first time pulping: After the wear-resistant material absorbs a certain amount of moisture, the pulping operation is performed using a machine, and a leveling tool is used to level the slurry. The second time the material was spattered: After the hardening of the wear-resistant material reaches a certain stage, a prescribed amount of 1/3 of the material is used for the second time, and the slurry is spouted by mechanical means. The second pulping: consistent with the first pulping operation. Mechanical trowels receive light: According to the hardening of the ground, use a mechanical trowel to receive light. Maintenance: The ground is finished light, film maintenance or recommend special curing agent maintenance. Application: According to the weather conditions, use recommended professional cleaning and waxing, with obvious decorative and protective effect. The characteristics and construction process of the above- mentioned emery wear-resistant floor materials are briefly introduced here, and I hope to help you. For more information, please visit this website. Stay tuned. What is the tile wear-resisting mat
Color: White, Black, Red, Blue, Beige, Green, Grey, etc.
Thickness: 0.4-250mm
Size: 1220*2440/1000*2000/1500*3000 mm
Application:
1) cutting and Chopping Board in abattoir, meat works and fish markets
2) spacers between steel plates
3) gears and rollers
4) wear strips
5) linings for chutes and hoppers
6) scraper blades
7) transfer tables
8) drag conveyor flights
Chopping Board, Polyethylene Sheet, HDPE Sheet, PE Plastic Sheet,Good Grade Sheet SHENZHEN XIONGYIHUA PLASTIC INSULATION LTD , https://www.xyhplastic.com
