Precautions for the use of woodworking saw blades

September 13, 2019

1. The machine should have good performance and no swing;

2. The size of the flange should be the same, which is 1/3 of the diameter of the saw blade;

3. The surface of the flange should be flat, clean and perpendicular to each other;

4. The gasket should be absolutely vertical;

5. The shaft should be flat and straight and the tolerance is not over H7;

6. The saw blade should be cleaned before installation. If the saw is stuck with resin, it needs to be diluted and wiped off;

7. If the saw blade has a blunt sensation, it should be repaired in time and pay attention to keep the original cutting angle of the sawtooth;

8. When grinding, not only the right diamond grinding wheel but also the cooling fluid should be used.

9. It is recommended that the saw blade reaming does not exceed 20 mm of the original hole. Otherwise, the saw blade cutting effect will be affected if the loss occurs.

10. Each installation must ensure that the flanges and gaskets are clean and flat;

11. When grinding the back angle and the saw body, be careful not to manually operate it, which will cause the sawtooth to break and the saw body to be unbalanced;

12. When installing the row saw, pay attention to the same level of the iron frame and the material table;

13. Before cutting, check that the saw blade has been installed and the one side saw blade slips on the shaft.

Global hardware network

Concerned about surprises

Tag: woodworking saw blade

Previous: How to buy the kitchen sink Next: How to break the update equipment for machine tool tools

Kemtron KTL 48 Shaker Screen

Replacement KEMTRON KTL 48 Series Shale Shaker Screen – Steel Frame

SJ- Kemtron KTL-48 Shaker Screen is the replacement screen which is compatible with KEMTRON 48 series shale shakers. For maximizing the solids removal and discharge dryness, please contact us for ideal screen selection advice according to the practical flow rate and solids type. Please don't attempt to use sealant to extend the life of the screen, screen saver plugs are the wise choice and will seal off any broken cell within the screen.


Technical Parameter

  • Mesh Material: stainless steel 304/316/316 L.
  • Frame Material: Q235 steel.
  • Screen Type: XL, XR.
  • API RP 13C Designation: API 20 – API 230.
  • Package: packed in paper carton, shipped by wooden case


Adaptable Shale Shaker Model

SJ-Kemtron KTL-48 shaker screen  are used as the substitute screen for

  • KEMTRON KTL 48 shale shaker.
  • KTL-448 AG four panel shaker.
  • KTL-48 STD three panel shaker.
  • KTL-48D three panel shaker.
  • KTL-48 SS three panel shaker
  • KEMTRON 48 series desander.
  • KEMTRON 48 series desilter.

Competitive Advantage

  • Sturdy steel frame tube welded to multi-ribbed construction.
  • 100% interchangeable with OEM brands screen panel size.
  • SS 304/316 wire mesh cloth does not rust or delaminate.
  • Manufactured according to the API RP 13C (ISO 13501).
  • Scientific & reasonable cost control system for competitive price.
  • Adequate inventory in the shortest time to meet customers' demand.
Kemtron KTL 48 Shaker ScreenKemtron KTL 48 Shaker ScreenKemtron KTL 48 Shaker Screen


Kemtron Ktl 48 Shaker Screen

Kemtron Ktl 48 Shaker Screen ,Derrick Shaker Screens,Kemtron Kpt 28 Oil Shale Shaker Screen ,Shale Shaker For Sale

Anping Shengjia Hardware Mesh Co.,ltd , https://www.oilshakerscreen.com