Treatment of roof leaks First of all, the leaking of the roof must first be leaked. The leak is taken from there. The main reason is to look for leaks from the high and low points of the roof (because the water flows down to the bottom). First of all, see if there is any crack in the roof. Aging, there is no air bubble in the original SBS waterproofing membrane on the roof. If there is air bubbles, it proves that the water has entered the bottom of the waterproof layer, so that it leaks. There is also no gutter on the roof. In the countryside, there are still In a large number of tile houses, when there is a roof leakage due to tile damage, just replace the tiles. This step is also referred to as “turnoverâ€. Most of the rural roofs are prefabricated panels. Usually, there is a connection between the boards and the board where the water leaks. Therefore, the simple and costly method of repairing leaks in the top of rural flats is to lay a layer of asphalt on the roof. The seams are stuck, but this method does not have a long-lasting waterproof effect; the more durable method is to use a waterproof layer on the left side of the roof or apply latex. Treatment of roof leaks II If there is a large area of ​​water leakage or multiple water leaks on the roof, professionals will check for cracks. After processing the cracks according to the previous plan, waterproof membranes shall be placed on the entire roof to enhance the waterproof effect. The upper insulation board, because the height of the insulation board is more than 20 cm, can achieve the double effect of protecting the waterproof layer and heat insulation. Households who are reluctant to use thermal insulation panels may consider the use of wire mesh concrete (the technical term is wire mesh fine stone mortar), and the leakage prevention effect is also very good. Cracks in the wall surface seepage of water, under normal circumstances professional construction team will use the basket, by the maintenance staff in the external wall construction. Treatment is: large cracks can be used to plug the king, small cracks can use glass glue to make up for leaks, repair with exterior wall waterproofing agent, after spraying a few roads on it. As the external wall cracks need to be trapped and work at heights, the public must ask a professional construction team to handle it to prevent the release of safety accidents. In addition, the citizens should also pay attention to the fact that the roof must be dry before waterproof repair work is done because the moisture in the roof does not evaporate, and the new waterproof layer will be lifted, and the waterproof effect will immediately fail. Therefore, it is not suitable to construct in rainy weather. It is necessary to wait until the sun has dried the water before it can be used. Secondly, if the roof is not only waterproof, you only need to remove the leaked part 2~3cm deep and then clean it. You will use bitumen to pour it. Now there is finished bituminous coating. When it is sunny, it will not be treated basically. Leaked. If there is a waterproof layer, it's more troublesome. To remove water around a piece of water, make it waterproof again. When doing it, pay attention to the reinforcement layer at the junction with the original waterproof. There are many ways to deal with leaks, or find some professional leak-proof companies to deal with this issue. The roof leakage in buildings in the city is inseparable from the construction quality. Generally, the top leakage of the houses is caused by the foundations and the problems caused by the floor slabs. This is the problem that the developers need to solve. Therefore, the roof of the urban building is leaking and the property needs to be let. The company handles it. Treatment of roof leakage When leakage occurs in the roofs of some of the city's red roofs, the effect of leakage prevention is the same as long as the grass, moss or dust on the tiles are removed and the tiles are replaced. For flat roofs, where there are obvious cracks in the roof, use a tool to split the cracks into "V" or "U" shape, fill with caulking ointment, and fill with water-proof coils over and around the cracks. If you want to enhance the leak-proof effect, you can also put a waterproof membrane. Tips: More practical decoration knowledge, real scene with the shoot, please pay attention to the palm of this site (micro signal: mall_jia). Home knowledge
1.Type
forged Pipe Fitting 3000 class tee
2.Size
Seamless 1/2" To 48" Welded To 72"
3.Wall thickness
Sch5S-Sch160, XS,XXS
4.Standards
ANSI, ASME,ASTM,DIN, JIS, BS, ISO, GB, SH, AND HG etc
5.Material
Stainless Steel: ASTM A403 WP304, 304L, 310, 316, 316L, 321, 347, 904L
Carbon Steel: ASTM A234 WPB, WPC ASTM A105 WPHY 42, 46, 52, 56, 60, 65, 70, 80
Alloy Steel: ASTM A234 WP1, WP5, WP9, WP11, WP22, WP91 Low Temperature: ASTM A420 WPL 1, WPL 3, WPL 6
6.Surface treatment
Black painting,anti-rust varnish,anti-rust oil,hot galvanized,3PE coating, epoxy coating.
7.Certificate
API, CCS,and ISO9001:2000
Forged Fitting Forged Fitting,Forged Coupling,Pipe Forged Fitting,Forged Union Shijiazhuang Huize Pipe Fitting Co., Ltd. , https://www.huizegd.com
Do not be afraid of the roof leaking 4 strokes to teach you to get!
Not afraid of rainy days, afraid of fear of leaking houses! The leakage of water in our houses has brought great troubles to our lives and has greatly affected our daily life. For example, leakage of water in a house can cause dampness or even corrosion of furniture, mildew on the walls, etc. Therefore, it is urgent to deal with leaking roofs. Everyone talk about what processing methods!