Elegant insect protection roller blind for window/door Roller Insect Screen,Insect Screen,Insect Door,Insect Screen Door Huanghua Techo Building Material Co., Ltd. , http://www.insectsscreen.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge>Fracture analysis of stepping motor and its control system of bearing grinding machine in China Fault Analysis of Stepping Motor and Its Control System of Bearing Grinding Machines in China
China's bearing grinding machine stepper motor and its control system followed by a large number of stepper motor control bearing grinding machine facing the city. Pouring low morning 刂 frequency Naifu 庖 åš¼ 丛 丛 丛 éŠå¦« éŠå¦« éŠå¦« éŠå¦« éŠå¦« éŠå¦« éŠå¦« éŠå¦« éŠå¦« éŠå¦« éŠå¦«Low car Nai 饣 饣 傩豢墒 嵋陨 嵋陨 嵋陨 嵋陨 嵋陨 ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ ç¼ å·¢ å·¢ å·¢ å·¢ å·¢ å·¢ å·¢ å·¢ å·¢ å·¢ å·¢ /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
The stepping motor system presents many problems. We have done research on the inner ring groove grinder of the ball bearing; we have tried several stepping motors of several brands in China; we found that the different steps of the two systems are very serious. Not the same. Step error test starts from PLC, position control module, stepper motor driver and stepper motor.
The lead screw lead is 4mm; the harmonic reducer has a reduction ratio of 1:80; the step angle is 0. 9° The repeated positioning error of the stepping motor has now exceeded 3 times the machine tool accuracy specification. The pulse equivalent is 0. 125μm accounting; the cumulative repeat positioning error of the workbench has reached 0.00 in 20 times. The data in Table 1 clarifies not only the error of the stepping motor; the error of the mechanical system becomes more and more significant.
We analyzed the feed organization and compensation organization of this machine tool; found that the mechanical problem is also severe. The top of the list; the nominal diameter of the ball screw is small (Φ20); the accuracy level is lower than the level 3; and the hand feel is more severe, the second Feeding fast-jumping cylinder and ball screw depicting positioning; installation orientation error can not be eliminated, third; harmonic reducer and ball screw as long as the screw is locked without key connection or pin connection, fourth; no ball screw is selected Bearings, etc.
Then we analyzed the electrical system of the machine tool; found that the inverter, transformer and stepper motor controller are placed close to each other; the data cable from the PLC output is not shielded; the combination of strong and weak power cables with the disk These problems are all factors that affect the instability of the stepper motor system. The pulse equivalent is 0. 125μm.
Because the anti-interference of China's stepper motor system can be poor; the irrationality of these electrical drawing plans will directly lead to accidental feed system and compensation system errors; plus the systematic errors of the mechanical system; the machine tool will be in unstable operation. situation.
It is not to say; as long as the hydraulic feed compensation system of the machine tool is changed into the stepping motor feed compensation system; the whole induction function of the machine tool will definitely advance significantly. The stepping motor replaces the original messy hydraulic feed compensation system; The error of the hydraulic shake and mechanical parts processing drive chain is eliminated; and the stepping motor can divide the feed process into several periods; each period can use different pulse frequency to control the feed speed; the number of pulses can be used to control the machine The workbench is fine-grained; this is indeed a big step forward than the bearing grinders of the original hydraulic system. However, it is followed by the other associations of the machine tool, which are also updated with the description; the satisfaction of the grinding machine skills needs of the machine. The depiction of the mechanical layout is still the depiction of the electrical system. It should not ignore the anti-jamming characteristics of the stepper motor system. It is assumed that the solution to the above problems is not properly solved; it is assumed that all the components of the machine are especially critical. The components are still the specifications of the original mechanical hydraulic system machine tools; the bearing grinding machine controlled by the stepper motor system Will not be improved in essence.
Of course; the most complete method is to select the world's most advanced servo motor control system. Select the bearing grinding machine of the servo motor control system; remove the fast jump cylinder and the harmonic reducer; use the ball screw and the servo motor to directly connect the layout; Mechanical system errors are minimal. Although China's choice of servo motor control system bearing grinding machine is still mostly pulse control; but the induction motor drive induction; anti-interference ability and repeat positioning accuracy; compared to stepper motor bearing grinding machine has made a big move Step. Because of the characteristics of the stepper motor system and many bugs; it only mechanical hydraulic control to advance to a transition product of the servo system control center; foreign countries now rarely see the fine grinding machine controlled by the stepper motor system; The most advanced country in the use of stepper motor system on CNC machine tools. Following the acceleration of China's bearing professional technical reform speed; followed by the development of more and more high-quality bearing companies; the end of the bearing grinding machine controlled by the stepper motor will be servo motor Replacement.
Recommend to friends comments close window Bearing related knowledge Analysis of the advantages and disadvantages of the NSK rolling bearing. Analysis of the super-finishing process of the bearing ring. Analysis of the bearing material without smooth bearing (1)
Commonly used to adjust the radial clearance of KOYO bearings
NSK imported bearing one-way bearing ferrule processing process
This article links to http://
Please indicate the bearing network http://
Previous:Improvement of the control method of the spindle of the machine tool. The next part: the process of rolling bearing load accounting
Screwing mounting into the wall.
Long-lasting, sturdy, powder-coated aluminium aluminium profiles
UV-resistant and tear-resistant fiberglass fabric
Smooth rolling of the roller blind in a compact aluminium cassette
Rollo individual, open and close either with two handles
The ideal solution for various window/door airing without being disturbed by annoying insects
EN13561-2015 certification:
Resistance to wind load: Class 1
Operating effort: Class 1
Mechanical Endurance: Class 1
Resistance to corrosion: Class 2
As the professional Insect Screen supplier, we cooperated with consumer from all the world to settle the insect problem.
Fault Analysis of Stepping Motor and Its Control System of Bearing Grinding Machines in China
Source: China Bearing Network Time: 2017-11-27